Launch X431 IMMO Plus Диагностический инструмент

Additionally, the Launch X431 IMMO Plus provides complete OE-Level system diagnosis with 39 reset services, full bi-directional control (active test), and FCA "Auto Auth" Access. It also features a 2-year free update, auto scan, remote diagnostics, and diagnostic feedback capabilities.

The Launch X431 IMMO Plus offers several anti-theft benefits, including support for VW/Audi MQB engine ECU replacement or clone without the need for car engine ECU original data, direct key access to the Audi replacement (0AW/0B5) Fifth Generation Transmission ECU, and support for more than 170 types of Bosch engine ECUs and various European, American, and Asian models.

Furthermore, the Launch X431 IMMO Plus provides anti-theft IMMO password reading, IMMO programming for Car Key Chip Read/Write, EEPROM Chip Read/Write, MCU Chip Read/Write, EEPROM and Flash Read/Write Engine ECU and Transmission ECU, and anti-theft compliance for 60 brands of independent immobilizer software for American, European, and Asian models.

Launch X431 IMMO Plus supports the replacement of the immobilizer module, key selection for numerous models such as Ford, GM, Mercedes-Benz, BMW, Volkswagen, Audi, Chery, Porsche, Peugeot, Citroen, Land Rover, Jaguar, Honda, Haval, Toyota, Nissan, Renault, Suzuki, Hyundai, Kia, GWM, and JAC cars.

Launch X431 X-PROG3 Features and Functions:

The Launch X431 X-PROG3 is a comprehensive vehicle diagnostic tool that offers an array of features for effective troubleshooting. Some of its key features include:

Car key slot: The car key slot enables users to perform key matching functions by placing the car key in it.

Mercedes-Benz key infrared slot: This slot is designed to accommodate Mercedes-Benz infrared keys for performing key matching functions.

Car key hole: The car key hole can be used for matching keys by inserting the key chip.

Status indicator: The device is equipped with a power indicator to display its status.

DIY slot: The DIY slot allows users to connect the anti-theft computer pin through a cable for reading and writing data.

Locker install chip burning socket: This socket supports FULL EEPROM or MCU data read and write operations.

DC12V power supply: The device can be connected to a DC12 power supply.

DB15: The main wiring can be connected to the device via the DB15 port.

LAUNCH X431 IMMO Plus provides full system diagnostics at an OE level, allowing users to access almost all car ECUs to read and clear codes, extract real-time data, freeze frame, and obtain ECU information. It can also perform active tests, adapt, match, turn off signal lights, reset monitors, and diagnose a wide range of car models and systems. Some of the systems it can diagnose include ABS systems, engine systems, SAS systems, TPMS systems, IMMO systems, battery systems, oil service systems, SRS systems, DPF systems, air conditioning systems, transmission systems, and more.

With its active component tests, also known as drive tests, the Launch X431 IMMO PLUS can locate vehicle problems and help determine if any system, component, or subsystem is working correctly. The device's bi-directional control function enables it to perform active tests, such as turning the fuel pump on and off, to quickly identify wiring, relay, or pump problems without requiring the removal of any parts. Note that some of the device's features may not be available for all vehicles.

LAUNCH X431 IMMO PLUS supports 39+ reset services, including the following functions:

1. Oil Reset Service: This function resets the oil service for the engine oil maintenance system, which calculates the optimal oil life change interval based on driving and weather conditions. It should be performed when the service lamp is on or when the engine oil or electrical instruments that monitor oil life are changed.
2. Electronic Parking Brake Reset: This function resets the brake pad after replacing it. It should be performed when the brake pads and brake pads have been replaced, the brake shoe indicator is on, the brake pad sensor circuit is short (recoverable), or the servomotor has been replaced.
3. Steering Angle Calibration: This function resets the steering angle after replacing the steering position sensor, mechanical parts, four-wheel alignment, or restoring the car body. To reset the steering angle, the ECU overrides the exact angle for left and right steering.
4. ABS Bleeding: This function enables bi-directional tests to test the working conditions of the anti-lock braking system (ABS). It should be performed when the ABS contains air, or when the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake fluid are replaced.
5. Transfer Learning: This function allows you to carry out the car teeth learning to turn off the MIL. It should be performed after replacing the engine ECU, Crankshaft Position Sensor, or Crankshaft Flywheel or when the DTC "Tooth not learning" is present.
6. IMMo Service: This function performs the anti-theft key matching function when the immobilizer control system on the car detects and authorizes remote keys for normal car use. It should be performed when the ignition key, ignition switch, combined instrument panel, ECU, BCM, or remote control is replaced.
7. Injector Coding: This function writes the actual injector code or overwrites the code in the ECU with the corresponding cylinder's injector code to more accurately control or correct the injection amount of the cylinder. It should be performed after replacing the ECU or injector.
8. Battery Maintenance System Reset: This function resets the vehicle battery monitor, clears the original low battery fault information, and performs battery matching. It should be performed when replacing the main battery or battery monitoring sensor.
9. Diesel Particulate Filter (DPF) Regeneration: This function cleans the PM (particulate matter) from the DPF filter through continuous oxidation combustion mode. It should be performed when the exhaust gas back pressure sensor has been replaced, PM trap removed or replaced, nozzle fuel additive removed or replaced, catalytic oxidizer removed or replaced, DPF regeneration MIL enabled and maintenance done, or DPF regeneration control module replaced.
10. Electronic Throttle Position Reset: This function makes initial settings for the throttle actuators and returns the received values stored on the ECU to the default state. This allows precise control of the actions of the control throttle (or idle motor) to adjust the amount of air intake.
11. Gearbox Matching: This function completes the gearbox self-healing to improve the quality of gear shifting. It should be performed when the gearbox has been disassembled or repaired.
12. AFS (Adaptive Front Lighting System) Reset: This function initializes the adaptive headlamp system.
13. Solar Roof Initialization: This function sets the sunroof lock, closed when it rains, sliding/tilting, roof memory function, temperature threshold outside caretc.
14. Suspension Calibration: This function adjusts the body height. It should be performed when replacing the body height sensor or control module in the air suspension system or when the vehicle height is incorrect.
15. EGR Adaptation: This function is utilized to analyze the performance of the Exhaust Gas Recirculation (EGR) valve after it has been replaced or cleaned.
16. Seat Calibration: This function is applied to synchronize the seats with the memory function during rebuilding and repairing.
17. Tire Reset: This function is employed to establish the parameters for modified or replacement tire size.
18. Coolant Bleeding: Use this function to activate the electronic water pump prior to venting the cooling system.
19. AdBlue Reset (Diesel Exhaust Filter): After replenishing or replacing the diesel exhaust gas cleaning fluid (vehicle urea), AdBlue operation is required.
20. NOx Sensor Reset: The NOx sensor is responsible for detecting nitrogen oxides (NOx) present in engine exhaust gases. If the NOx catalytic converter is replaced, and the NOx fault is reinitialized, the Learned Catalytic Converter Value must be reset in the engine ECU.
21. AC System Initialization: Relay/AC system initialization must be performed when the AC drive is replaced, or ECU memory is lost.
22. High Voltage Battery Detection: This function is used to diagnose high voltage batteries and determine their status.
23. Windows Calibration: This function is utilized to synchronize the window and door settings to restore internal memory and restore the automatic window power function.
24. Language Change: This function is employed to modify the language used by the vehicle's center console system.
25. Reset AF: This function is used to establish or learn the parameters of aviation fuel consumption.
26. Transport Mode: To reduce vehicle power consumption, the user can limit the vehicle's speed, not wake up the network to open the door, disable the remote key, etc. In this case, deactivation of various modes of transport requires the vehicle's hard and floppy drives.
27. Reset Start/Stop: This function is utilized to activate or deactivate the automatic Start/Stop function by setting a hidden function in the ECU (provided the vehicle is equipped with hidden function and hardware support).
28. Intelligent Cruise Control Reset: This function is employed to synchronize the Intelligent Cruise Control module after it has been replaced or repaired.
29. Engine Power Balance Monitoring: This function is used to monitor the acceleration of the crankshaft in each cylinder of power and determine the relative power provided by each cylinder.
30. Gas Particulate Filter (GPF) Regeneration: This function is used to replace or regenerate the GPF after an increase in fuel consumption and a decrease in engine output due to long-term maintenance of the GPF.
31. Motor Angle Calibration: This function is used to perform motor rotation angle calibration when the rotor position detected by the motor angle sensor differs from the actual position of the rotor field.
32. Automatic Reset of Air Conditioning Initialization Software (ACINI Reset)
33. Electronic Water Pump Starts Reset (Coolant Reset)
34. ECU Reset
35. FRM Reset
36. Clutch Reset
37. Gate Reset
38. Turbo Reset
39. RLSensor Reset